1. Check whether each water tank is short of water and full of water, and whether the tire pressure meets the requirement of 2.5bar_ I'm not sure.

2、檢查發動機機油油尺，液壓油箱標尺，齒輪箱油標觀察孔，前、后橋，輪邊減速軸頭擰開油面油堵檢查齒輪油是否符合要求，缺少應及時添加，總泵自動液油杯液面是否合乎標準要求。

2. Check the engine oil dipstick, hydraulic oil tank ruler, gearbox oil level observation hole, front and rear axle, wheel side reducer shaft head, screw off the oil level oil plug, check whether the gear oil meets the requirements, if it is missing, add it in time, and whether the automatic oil cup level of master cylinder meets the standard requirements.

3、觀測發動機機油，齒輪油，檢查油標尺，油標鑼孔，液壓油箱時，車輛要水平位置。

3. Observe the engine oil, gear oil, check the oil dipstick, oil mark, Gong hole, hydraulic oil tank, the vehicle should be in a horizontal position.

4、全車各部油管路，氣管路接頭是松動有無漏油，漏氣現象。檢查全車線路有無接觸不良，各儀表，燈光是否工作正常。

4. The oil pipes and gas pipe joints of all parts of the car are loose, whether there is oil leakage or air leakage. Check if there is poor contact in the whole vehicle line, and if all instruments and lights work normally.

5、行駛前剎車是否制動有效，檢查各操縱閥作用是否良好。

5. Check whether the brake is effective before driving, and check whether each control valve works well.

各操作閥的作用

Function of each operating valve

1、主車前后行走操縱閥( 快慢檔，前進和倒車檔)-般行走時為前駕，施工作業時為后駕。

1. The front and rear travel control valve (fast and slow, forward and reverse gears) of the main vehicle is generally the front drive when walking, and the rear drive when working.

2、大臂升降旋轉操縱閥，舉料，左右旋轉罐體控制。

2. Boom lifting rotary control valve, lifting, left and right rotary can body control.

3、料斗上下料操縱閥，鏟料、卸料控制鏟斗作用。

3. Hopper loading and unloading control valve, shovel, discharge control bucket function.

4、手動油門操縱閥，控制發動機的轉速，使攪罐在一定的平穩速度下旋轉。

4. The manual throttle control valve controls the speed of the engine to make the stirring tank rotate at a certain steady speed.

5、座椅腳踏定位卡銷，用于座椅調轉方向時起到鎖止作用，踏板踩向下時。鎖銷打開，左翼轉到位置后制動鎖止。

5. The foot positioning pin of the seat is used to lock the seat when the seat rotates, and when the pedal is depressed. When the lock pin is opened and the left wing is turned to the position, the brake is locked.

今天的全自動自上料攪拌車精彩內容就給大家分享到這了，更多的精彩內容請點擊我們的網站http://www.ranhaofz.cn進行關注留言，后續會有更多的精彩內容為您呈現.

Today's automatic self feeding mixer wonderful content to share with you, more wonderful content please click on our website http://www.ranhaofz.cn Follow the message, there will be more wonderful content for you