Tips on the use of automatic feeding mixer

攪拌車在出現故障的時候，需要及時將內部的混凝土清理出來，通常有兩種方法清理：

When the mixer truck breaks down, it is necessary to clean the internal concrete in time. There are usually two methods to clean it:

方法一：

Method 1:

1.準備好緊急驅動軟管，將攪拌車熄火，卸下液壓馬達上的高壓油管接頭。

1. Prepare the emergency drive hose, turn off the mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.

2.將救援車熄火，將其液壓馬達的高壓油管卸下，并與故障車上的對應接頭用緊急驅動軟管相連。

2. Turn off the rescue vehicle, remove the high-pressure oil pipe of its hydraulic motor and connect it with the corresponding connector on the faulty vehicle with emergency drive hose.

3.發動救援車，將其操縱手柄撥至出料位置，故障車內的混凝土即被排出。

3. Start the rescue vehicle, turn its control handle to the discharge position, and the concrete in the faulty vehicle will be discharged.

4.緊急驅動完畢后，將驅動軟管卸下，并恢復兩車原狀。

4. After the emergency drive, remove the drive hose and restore the two vehicles to their original state.

方法二：

Method 2:

在托輪和滾道之間放入木楔，以控制攪拌筒的旋轉，一定要注意身體；將發動機熄火，拆松液壓馬達的一根高壓油管，攪拌筒可自由旋轉，控制攪拌筒的旋轉，使維修孔轉到下部，然后打開維修孔，清理出筒內混凝土。混凝土排出完畢后，恢復攪拌車原狀。在一般情況下，多數人會選擇用方法一來解決，當方法一解決不了時才會選擇方法二。

Put a wooden wedge between the supporting wheel and the raceway to control the rotation of the mixing drum. Be sure to pay attention to your body; Turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, the mixing drum can rotate freely, control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then open the maintenance hole to clean the concrete in the drum. After the concrete is discharged, the mixer truck shall be restored to its original state. In general, most people will choose method one to solve it, and only choose method two when method one can't solve it.

特別是灌樁發熱：

In particular, cast-in-place pile heating:

1.油泵吸油口的過濾網是否堵塞了，拆出濾網清洗一下，再試試追問剛換的柱塞 泵和馬達全大修的。

1. Check whether the filter screen at the oil suction port of the oil pump is blocked, remove the filter screen and clean it, and then try to ask about the overhaul of the plunger pump and motor just replaced.

2.在裝管的時候，密封性是有沒有裝好，有沒有可能漏氣 。

2. When installing the pipe, whether the sealing is well installed and whether there is possible air leakage.

3.檢測壓力是否正常 。

3. Check whether the pressure is normal.

4.檢查連軸器是否出現發熱。以上是自動上料攪拌車的相關知識，歡迎大家多多關注我們的網站！

4. Check whether the coupling is heated. The above is the relevant knowledge of automatic loading mixer. Welcome to pay more attention to our website!

本文由全自動自上料攪拌車為您提供，我們的網站是：http://www.ranhaofz.cn/我們將以全心全意的熱為您提供服務，歡迎您的訪問

This article is provided for you by the automatic self loading mixer. Our website is: http://www.ranhaofz.cn/ We will serve you wholeheartedly. Welcome to visit