The automatic feeding mixer is composed of two parts: main parts and working device. The main components are required by all automatic feeding mixer trucks. The working device is unique for different purposes.

一、主要部件包括發動機，變矩器，變速箱，前、后驅動橋，簡稱四大件：

1、 The main components include engine, torque converter, gearbox, front and rear drive axles, which are referred to as four major parts for short:

1、發動機。

1. Engine.

2、變矩器上有三個泵，工作泵（供應舉升，翻斗壓力油）轉向泵（供應轉向壓力油）變速泵也稱行走泵（供應變矩器，變速箱壓力油），有些機型轉向泵上還裝有先導泵（供應操縱閥先導壓力油）。

2. There are three pumps on the torque converter, working pump (supply lifting and tipping pressure oil), steering pump (supply steering pressure oil) variable speed pump, also known as travel pump (supply torque converter and transmission pressure oil). Some models of steering pump are also equipped with pilot pump (supply control valve pilot pressure oil).

3、工作液壓油路，液壓油箱，工作泵，多路閥，舉升油缸和翻斗油缸。

3. Working hydraulic oil circuit, hydraulic oil tank, working pump, multi-way valve, lifting cylinder and tipping cylinder.

4、行走油路：變速箱油底殼油，行走泵，一路進變矩器一路進檔位閥，變速箱離合器。

4. Traveling oil circuit: transmission oil pan oil, traveling pump, one way to the torque converter, one way to the gear valve, and transmission clutch.

5、驅動：傳動軸，主差速器，輪邊減速器。

5. Drive: transmission shaft, main differential, wheel reducer.

6、轉向油路：油箱，轉向泵，穩流閥（或者優先閥）轉向器，轉向油缸。

6. Steering oil circuit: oil tank, steering pump, steady flow valve (or priority valve), steering gear and steering cylinder.

7、變速箱有一體的（行星式）和分體的（定軸式）兩種。

7. There are two kinds of transmission: integrated (planetary type) and split (fixed shaft type).

二、工作裝置：

2、 Working device:

自動上料攪拌機的上料和裝卸物料作業是通過其工作裝置的運動來實現的。

The feeding and loading and unloading operations of the automatic feeding mixer are realized through the movement of its working device.

在我們的生活中，混凝土攪拌車是用于運輸混凝土的特殊車輛，通常在該車輛后方裝有一個大罐來攪拌混凝土。但是，由于需要長期清潔車輛內部的混凝土，因此下面介紹具體的清潔方法。

In our life, concrete mixer is a special vehicle used to transport concrete. Usually, a large tank is installed at the rear of the vehicle to mix concrete. However, since the concrete inside the vehicle needs to be cleaned for a long time, the specific cleaning methods are described below.

1.準備應急驅動軟管，關閉攪拌車，并卸下液壓馬達的高壓油管接頭。

1. Prepare the emergency drive hose, close the mixer truck, and remove the high-pressure oil pipe connector of the hydraulic motor.

2.拆下高壓油管，并用緊急驅動軟管將其連接到故障汽車的相應接頭。

2. Remove the high-pressure oil pipe and connect it to the corresponding connector of the faulty vehicle with the emergency drive hose.

3.對于發動機攪拌車，將控制手柄轉到卸料位置，以去除攪拌車內的混凝土。

3. For the engine mixer, turn the control handle to the unloading position to remove the concrete in the mixer.

4.應急驅動器完成后，卸下驅動器軟管，將車輛恢復到原始狀態。

4. After the emergency drive is completed, remove the drive hose and restore the vehicle to its original state.

由于您中有些人可能已經知道如何清潔混凝土攪拌車內的混凝土，因此了解這些知識更好，以防止在使用過程中出現故障對設備正常運行的影響，我希望您能夠做到這一點。

Since some of you may already know how to clean the concrete in the concrete mixer truck, it is better to understand this knowledge to prevent the impact of failure on the normal operation of the equipment during use. I hope you can do this.

以上就是為大家介紹的有關全自動自上料攪拌車的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.ranhaofz.cn/

The above is a detailed introduction to the automatic self feeding mixer truck. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.ranhaofz.cn/