At present, the market demand for concrete mixer is very large, many people buy it. The production process is also very professional. What do you know about the bearing production process of the mixer?

　　攪拌機軸承設計和生產過程中,必須考慮到軸承熱平衡控制溫度上升,由于軸承摩擦條件下,功耗,由于內部摩擦和潤滑液進入熱引起的溫度升高,潤滑油粘度,差距將會改變,將軟化巴氏合金軸承,嚴重時產生“燃燒”持有軸事故,攪拌機改善軸承維修和裝配質量,確保光滑,沒有斑點的軸承,定位凸點完好無損,數量的反彈0.5 - 1.5毫米,保證裝配后的軸承借助自己的軸承孔彈性接合緊密,復制軸承位置的上下兩塊軸承軸承座位飛機高于兩端應30 - 50微米,更高的數量可以確保按規定扭矩擰緊軸承蓋螺栓軸承和軸承后座位密切協調,產生足夠的摩擦力自鎖,軸承不松散,良好的散熱效果,防止軸承燒蝕和磨損,軸承工作面不能刮接觸模式匹配法做測量達到75% - 85%,不應刮使軸承和軸配合間隙的直徑。

　　In the design and production process of mixer bearing, the temperature rise of bearing thermal balance control must be taken into account. Due to the power consumption under the condition of bearing friction, the temperature rise caused by internal friction and heat entering of lubricating fluid, the viscosity and gap of lubricating oil will be changed, which will soften Babbitt alloy bearing and cause shaft holding accident of "burning" in serious cases. The mixer will improve the quality of bearing maintenance and assembly to ensure smoothness, No spot bearing, locating convex point intact, quantity rebound zero point five - One point five Mm, to ensure that the assembled bearings are elastically connected with their own bearing holes. The upper and lower bearing seats of the duplicated bearing positions should be 30-50 microns higher than the two ends of the aircraft. The higher number can ensure that the bearing cover bolts are tightened according to the specified torque and the bearing rear seats are closely coordinated, It can produce enough friction force and self-locking, the bearing is not loose and has good heat dissipation effect, so as to prevent the bearing from ablation and wear. The working surface of the bearing can not be scraped by the contact mode matching method for measurement up to 75% - 85%, and the diameter of the matching clearance between the bearing and the shaft should not be scraped.

　　攪拌機使用除了發動機,底盤部件,如維護,也必須做好準備,在混凝土攪拌罐的口清潔,在每一次具體的交付,及時清洗攪拌罐的料斗,粘附現象,這可以有效地減少混凝土的強度可以減少車輛維護、交錯的生產高峰和及時進料孔進入料斗,并且出料槽采用局部補焊，配上槽縫余量，以減少設備在加工過程中前后漏漿造成的漏漿現象，在保證設備完完率的基礎上限度的保證設備的清潔度。

　　In addition to the engine and chassis components, such as maintenance, the mixer must also be prepared to clean the opening of the concrete mixing tank. At each specific delivery, the hopper of the mixing tank shall be cleaned in time, and adhesion phenomenon can be effectively reduced. This can effectively reduce the strength of concrete, reduce vehicle maintenance, staggered production peak and timely feed hole into the hopper, In addition, the discharge chute adopts local repair welding and slot allowance, so as to reduce the leakage caused by slurry leakage before and after the processing of the equipment, and ensure the cleanliness of the equipment to the maximum extent on the basis of ensuring the completion rate of the equipment.

　　攪拌車的維護保養是攪拌車使用過程中必不可少的環節。我們應該盡我們的努力來涵蓋所有方面的維修攪拌車。

　　The maintenance of the mixer is an essential part in the use of the mixer. We should do our best to cover all aspects of the maintenance of the mixer.